An Inspection and Test Plan (ITP) is the document that defines what needs to be inspected, tested, or reviewed during a project, who is responsible for each activity, and under what conditions work must stop until a sign-off is obtained. In shipbuilding, the ITP is the primary tool for managing quality assurance across fabrication. It is reviewed and approved by the classification society before production begins, and it forms part of the quality documentation submitted for vessel certification.
The ITP does not replace technical documents like the WPS or the weld log. It organises all of them into a verification sequence, so that each stage of fabrication is matched to its required inspection activity. Without a structured ITP, quality control depends on individuals remembering to check the right things at the right time, which fails at scale.
What an ITP covers
A shipbuilding ITP identifies every significant fabrication activity and assigns it an inspection level. For welding, this means specifying which joints require visual inspection, which require non-destructive testing, which require dimensional checks, and which require a classification society surveyor to be present. The ITP also references the acceptance criteria that apply to each activity, typically citing ISO 5817 imperfection levels for weld quality and the relevant dimensional tolerances from the design specifications.
Each row in the ITP corresponds to a specific activity or phase. It records the responsible party (shipyard QC, owner’s representative, or classification society), the type of inspection required, the reference standard, the acceptance criteria, and where the result is to be documented. The completed sign-off column is the evidence that the activity was verified.
Hold, Witness, and Review points
ITPs distinguish between three levels of inspection involvement. A Hold Point requires production to stop until the authorised inspector has verified the activity and issued a formal release. Work cannot proceed past a Hold Point without that sign-off. Hold Points are reserved for critical activities where any defect would be difficult or impossible to rectify after the next production stage, such as a structural closing weld on a hull section or a hydrostatic pressure test.
A Witness Point notifies the inspector that an activity is taking place. If the inspector does not arrive at the scheduled time, production may continue, but the activity must be documented. A Review Point does not require physical attendance at all. It involves verifying documentation, such as material certificates, welder qualification records, or NDT reports, before or after the activity. All three levels are necessary: Hold Points prevent irreversible mistakes, Witness Points maintain oversight without creating bottlenecks, and Review Points ensure the documentation trail is complete.
Who approves the ITP and when
The shipyard drafts the ITP based on the contract requirements, the applicable classification society rules, and the relevant standards (typically ISO 3834 for welding quality and EN ISO 5817 for weld quality levels). The classification society surveyor reviews and approves the ITP before production begins. The owner’s representative or a third-party quality inspector may also be required to sign off, depending on the contract.
Once approved, the ITP is a controlled document. Any revision requires the same review and approval cycle. Using a superseded version of the ITP on the shop floor is a common audit finding and can invalidate inspection records attached to the wrong revision. See how SOCWeld supports ITP and weld documentation management for maritime projects.
Common ITP failures in shipbuilding
The most frequent ITP failures during classification society audits are bypassed Hold Points (fabrication continued without the required sign-off), missing NDT results linked to the ITP activity, discrepancies between the ITP acceptance criteria and the inspection results recorded in the weld log, and version control failures where the shop floor was using an outdated ITP revision.
Retroactive documentation is another common problem. When ITP sign-offs are completed after the fact to catch up with production, the traceability breaks down. The sign-off is supposed to be the evidence that the inspection took place before production advanced. If the dates on the sign-offs do not match the dates on the weld log, auditors will flag the discrepancy.
Frequently asked questions
Is an ITP required for ISO 3834 compliance?
ISO 3834 requires documented inspection and testing activities as part of the quality system, but does not mandate that they be organised in a single document called an ITP. In practice, a structured ITP is the standard way of meeting this requirement and is expected by most certification bodies and classification societies. The ITP provides the verifiable evidence that inspections were planned and carried out systematically.
What is the difference between an ITP and a Quality Plan?
A Quality Plan defines the quality objectives and references the applicable standards for a project. An ITP operationalises those objectives by identifying the specific inspection activities, the responsible parties, and the acceptance criteria. The Quality Plan sets the framework; the ITP provides the activity-by-activity detail that makes the plan executable on the shop floor.
Can the same ITP be used across multiple vessels?
A standard ITP template can be reused provided the vessel type, classification society rules, and applicable standards are the same. Project-specific variables, such as the weld joint identifiers, the NDT percentages specified in the contract, and the owner’s hold points, must be updated for each vessel. A generic ITP that has not been tailored to the specific project will not pass classification society review.
Who is responsible for ensuring Hold Points are respected?
The shipyard’s Quality Manager and the production supervisors are responsible. The classification society surveyor and the owner’s representative have the right to enforce Hold Points, but the primary obligation to stop work lies with the shipyard. Bypassing a Hold Point without authorisation is a contractual and quality failure, regardless of whether it is later caught in the documentation review.
What NDT percentages are typically specified in a shipbuilding ITP?
This depends on the classification society rules, the structural zone, and the joint criticality. Primary structural welds on hull sections typically require 100% visual inspection and a defined percentage of radiographic or ultrasonic testing, often 10-25% for standard structural welds and 100% for critical joints such as main frame intersections, pressure-bearing connections, or joints under high cyclic stress. The exact percentages are defined in the ITP based on the classification society rules and the designer’s specifications.
SOCWeld links ITP activities to weld log entries and NDT results, so the sign-off trail is complete and auditable without manual cross-referencing. Book a demo to see how it works on a shipbuilding project.
